General-tools-and-instruments 849 Manual de usuario descargar pdf

Safety Instructions:

1. Always use eye protection when

using power tools. Wear safety

goggles that comply with ANSI 287.1.

2. WARNING: Always unplug drill from

power supply when changing bits and

attaching drill stops.

Before you get started:

The table below lists all the parts

included in the pocket jig kit.

Parts List:

ITEM # DESCRIPTION QUANTITY

1 Jig with screw clamp 1

2 Step Drill, 3/8" 1

3 Stop Collar 1

4 Hex Wrench 1

5 6" Square Drive 1

6 1-1/4" Wood Screws 24

Helpful Tips:

1. This pocket hole jig will accept work

pieces up to 1-1/2" thick.

2. It is always best to practice making

pocket holes on scrap pieces of wood

to familiarize yourself with the tool.

3. The jig is equipped with mounting

holes for easy attachment to a fixed

work surface.

4. Pocket hole joinery requires drilling

pocket holes in only one of the two

pieces to be joined.

E•Z POCKET HOLE JIG KIT INSTRUCTIONS

Figure 4

Figure 1

Figure 2

Figure 3

PATENT

#6,254,320

E•Z POCKET HOLE JIG KIT

PROJECT PLANS

How to Make a Stool

Instructions:

1. Drill four pocket holes in one end of each of the two

6" leg pieces (B) at the locations shown in the

diagram.

2. Drill two pocket holes in each end of the support

piece (C) at the locations shown in the diagram.

3. Place one of the legs (B) on your work bench with

the pocket holes facing up.

4. Screw the support piece (C) to the leg (B), centering

it left to right. (See Figure 1).

5. Place the other leg (B) on your work bench with the

pocket holes facing up.

6. Screw your support piece (C) to this leg (B),

centering it left to right so it mirrors the other side.

7. Place the stool top (A) on your work bench. Set the

legs and support (B & C) on top of your stool top (A)

and screw together. (See Figure 2).

8. Paint or stain as desired.

TOP (1)

LEGS (2)

CENTER SUPPORT (1)

GENERAL TOOLS & INSTRUMENTS 80 White Street New York, NY 10013

3567

• e-mail: [email protected] • www.generaltools.com •

Tools:

• Pocket Hole Jig Kit

• Electric Drill

Materials:

ITEM DESCRIPTION QUANTITY & LENGTH

A Stool Top (1" stock) 1 @ 8" x 12"

B Legs (1" stock) 2 @ 8" x 6"

C Support (1" stock) 1 @ 3" x 10-1/2"

Screws 12

Instructions:

1. Ensure the stop collar on the step drill bit is positioned at

the correct height on the step drill to prevent drilling into the

jig base (see Figure 1). Use the included hex wrench to

loosen/tighten the stop collar.

2. Center the work piece to be drilled in the jig and clamp

tight using the thumb screw (see Figure 2).

3. Drill the pocket hole(s) until the stop collar hits the base.

For cleaner cut holes and easier drilling, do not drill the entire

depth with one stroke. Instead, use short strokes until the

drill has reached its final depth (see Figure 3). When finished,

unclamp the work piece and remove from the jig.

4. Clamp the two work pieces together in the desired final

configuration. Drive screws (1-1/4" square head screws

supplied) into the pocket holes to complete the joint

(see Figure 4). Glue may be used in the joint if desired.

Figure 1

Figure 2

Figure 3

849 INSTRUCTIONS_06.11.07_SICHUAN 6/11/07 12:23 PM Page 4

1 2

Indice de contenidos

Pagina 1 - How to Make a Stool

Safety Instructions:1. Always use eye protection whenusing power tools. Wear safetygoggles that comply with ANSI 287.1.2. WARNING: Always unplug dril

Pagina 2

Instrucciones Para el Juego de Amortajadora E•Z Instrucciones de seguridad:1. Siempre use protección ocular cuando opereherramientas motorizadas. Use

Comentarios a estos manuales

Sin comentarios

General-tools-and-instruments 849 Manual de usuario

Busca en linea o descarga Manual de usuario para Herramientas General-tools-and-instruments 849. General Tools and Instruments 849 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas General-tools-and-instruments 849